Articles in this section

Configuration Parameters - NERO-RELAY

  • Updated

For information on how to configure parameters for your devices check out Adding configuration Parameters

Configuration parameters

Parameter no. 1 - Switch type I1

Sets the device to operate with either a momentary or a toggle switch.

Available settings (data type: 1 Byte DEC):

  • [DEFAULT] 0 - Momentary switch
  • 1 - Toggle switch

Parameter no. 10 - Participation in all on/off

Z-wave includes a special message type to tell all devices on the network to turn on or off. This isn't always desirable so it is possible to change how the device responds to these commands.

This will not change the functionality of the All Lights quick command on the NEXUS-NERO dashboard. Refer to the quick commands customisation article to change this feature.

Available settings (data type: 2 Byte DEC):

  • [DEFAULT) 255 - Responds to ALL ON and ALL OFF
  • 0 - Doesn't respond 
  • 1 - Responds to ALL OFF only
  • 2 - Responds to ALL ON only

Parameter no. 11 - Auto off delay

Sets the time delay for the output to turn off automatically after an on command is received from either the UI or the switch connected to i1.

Available settings (data type: 2 Byte DEC):

  • [DEFAULT] 0 - Disabled
  • 1-32535 - Time in seconds or milliseconds (see parameter 15)

Parameter no. 12 - Auto on delay

Sets the time delay for the output to turn on automatically after an off command is received from either the UI or the switch connected to i1.

Available settings (data type 2 Byte DEC):

  • [DEFAULT] 0 - Disabled
  • 1-32535 - Time in seconds or milliseconds (see parameter 15)

Parameter no. 15 - Auto on/off delay time

Sets the time unit for parameters 11, 12, 13, and 14 to be seconds or milliseconds.

Available settings (data type: 1 Byte DEC):

  • [DEFAULT] 0 - Seconds
  • 1 - Milliseconds

Parameter no. 30 - Save state on power failure

Your device can be configured to save its state in the event of a power failure and restore it when power is restored. In many cases, such as bedrooms, this may be undesirable behaviour.

Available settings (data type: 1 Byte DEC):

  • [DEFAULT] 0 - Saves and restores device state after power failure
  • 1 - Does NOT save state, device will always be "off" after power is restored

Parameter no. 40 - Power reporting %

Sets the percentage change in the power consumption of the device which makes the device report back to the network controller.

Setting this parameter too low can cause your wireless mesh to become busy and cause commands to not be sent or received correctly. We recommend not setting this parameter lower than 10.

Available settings (Data type: 1 Byte DEC):

  • [DEFAULT] 10 - 10%
  • 0 - Power consumption reporting disabled
  • 1-100 - Percentage change before reporting

Parameter no. 42 - Power reporting time

Sets the time interval in seconds which makes the device report back the power consumption to the NEXUS-NERO controller

Setting this parameter too low can cause your wireless mesh to become busy and cause commands to not be sent or received correctly. We recommend not setting this parameter lower than 300.

Available settings (Data type: 2 Byte DEC):

  • [DEFAULT] 300 - 5 minutes
  • 0 - Power consumption reporting disabled
  • 1-32535 - Time in seconds

Parameter no. 63 - Output contact selection

Sets the type of contact (NO or NC) at the output of the device

Available settings (Data type: 1 Byte DEC):

  • [DEFAULT] 0 - Normally open (NO)
  • 1 - Normally closed (NC)

Parameter no. 110 - Temperature sensor offset

Sets the offset value of actual measured temperature of the sensor which is reported back to the controller.

Available settings (Data type: 2 Byte DEC)

  • [DEFAULT] 32536 - Offset 0ºC
  • 1-100 - Value divided by 10 in ºC added to the measurement, e.g., 1 = 0.1°C, 100 = 10°C
  • 1001-1100 - Value divided by 10 (excluding the leading 1) in ºC removed from the measurement, e.g., 1001 = -0.1°C, 1100 = -10°C

Parameter no. 120 - Temperature reporting

Sets what amount of change is required in the sensed temperature before sending a new report to the controller.

Setting this parameter too low can cause your wireless mesh to become busy and cause commands to not be sent or received correctly. We recommend not setting this parameter lower than 5.

Available settings (Data type: 1 Byte DEC)

  • [DEFAULT] 5 - 0.5ºC
  • 1-127 - Value divided by 10 in ºC, e.g., 1 = 0.1°C, 127 = 12.7°C